Topic outline

  • From teachers:

    Dear students, if you wish to take this course, please read through this page carefully because this page includes an overview of course contents, implementation, teaching schedule, deadlines and grading criteria. Thank you.


    Wishing to get fundamentals knowledge to start understanding and designing modern electronic equipment including computers, vehicles, robots, satellites and any intelligent and autonomous systems? This is an essential course to start with, if you are interested in any activities of electronic equipment and systems! There is a continuation course "Electronic circuits" in the next spring semester after you get fundamental knowledge of circuits.

    1. Contents of the course

    1.1 Motivation and objectives
    This course aims at covering fundamentals to understand and design electronic circuits, aiming at introduction to 1) basic circuit components and Kirchhoff, Thevenin and Norton's theorems for simple direct-current (DC) circuit problems and 2) useful software simulation tool, e.g., KiCad, to solve a more complex circuit problems. Knowledge and skills learnt in this course will be essential for the next level of this course, i.e., "Electronic circuits" taught in the next spring semester and be helpful for electronics design labs.

    1.2 Learning Outcomes

    After this course, students get familiar with

    • Basic models and analysis methods of DC circuits, including operational amplifiers.
    • An electronic circuit simulation software and basic design and measurements of DC circuits.


    2. Course implementation

    2.1 Teachers
    • Prof. Katsuyuki Haneda, room 2143, TUAS building; teacher in charge
    • Prof. Martin Andraud, room 2192, TUAS building; lecture and exercise sessions
    • Senior University Lecturer Juha Mallat, room 2157, TUAS building; exercise sessions, simulation exercises
    • Mr. Lauri Vaha-Savo, room 2175, TUAS building; teacher
    • Mr. Ali Kourani, room 2142, TUAS building; teacher

    2.2 General organization
    This course is organized around three basic activities:
    • Lectures x 4, including 4 pre-assignments
    • Calculation Assignments x 12, to be returned during exercise return sessions
    • Simulations Assignments x 2, using the tool KiCad.  
    Note! Students must attend all teaching activities on Wednesdays (L01 series) and Thursdays (L02 series).

    2.3 The period I of autumn 2022 semester will be fully on-site teaching
    Following the University guidelines for the period I of the Autumn semester, contact teaching of this course will take place fully on campus.  All contact sessions are held in room AS6 of TUAS building, with exceptions when the number of students exceeds the room capacity. Teachers will communicate room changes with students through the annoucement channel of MyCourses. Remote activities may be organized due to teacher's needs.

    2.4 Schedule

    All lectures and exercise sessions are scheduled for 12-14, Finnish time. Lecture room AS6 of TUAS building.
    Date
    Sessions and deadlines Nilsson chapter Glisson chapter
    Lecturer
    Wed, Sep 7

    Introduction to this course - what we learn and why we learn about it?



    Katsu, Martin, Juha, Lauri, Ali

    Thu, Sep 8

    Lecture 1 - Kirchhoff theory


    2.1 2.2 2.4 3.1 3.2

    2.1-2.7, 3.1-3.9, 4.1, 4.2, 5.1, 5.2

    Katsu


    Wed, Sep 14

    Exercise session; Deadline of calculation assignment 1




    Katsu, Juha, Martin, Lauri, Ali

    Thu, Sep 15

    Lecture 2 - Circuit transforms


    3.3 3.4 4.9 4.10 4.13

    3.4-3.10, 4.3, 4.4


    Katsu


    Wed, Sep 21

    Exercise session; Deadline of calculation assignment 2




    Katsu, Juha, Martin, Lauri, Ali

    Thu, Sep 22

    Q&A session for simulation exercise (voluntary session; no need to join if not necessary. This session is ONLY in remote mode to share screens of KiCad.)


    Juha, Katsu


    Wed, Sep 28

    Deadline of simulation assignment 1 (NO contact session; just submit the assignment on MyCourses!)




    Thu, Sep 29

    Lecture 3 - DC circuit analysis methods


    4.1-4.6


    3.7, 3.8, 6.2


    Katsu


    Wed, Oct 5

    Exercise session; Deadline of calculation assignment 3




    Katsu, Juha, Martin, Lauri, Ali

    Thu, Oct 6

    Lecture 4 - Operational amplifiers


    5.1 - 5.5


    7.1-7.6


    Katsu


    Wed, Oct 12

    Exercise session; Deadline of calculation assignment 4


        Katsu, Juha, Martin, Lauri, Ali

    Thu, Oct 13

    Q&A session for simulation exercise (voluntary session; no need to join if not necessary. This session is ONLY in remote mode to share screens of KiCad.)
     
    Juha, Katsu


    Fri, Oct 14
    Deadline of simulation assignment 2 (NO contact session; just submit the assignment on MyCourses!)




    Note: this course does not have an exam.

    2.5 How to return exercises? [Important!]

    • Calculation exercises can be returned during exercise sessions only; see Calculation Assignments section.
    • Simulation exercises can be returned through MyCourses page only; see Simulation Assignments section.
    How flexible are deadlines? Deadlines of assignment submissions are clearly indicated in the schedule table above. Deadlines can be postponed only if a student agrees with one of teachers for a valid reason, e.g., sick leave, visiting a hospital, business trip, in advance of the above-mentioned deadlines. Otherwise the mentioned deadlines must be respected.


    2.6 Expected study efforts of students

    2 credits x 27.5 = 55 hours of study include

    • Self-study for pre-assignments: 1 hour x 4 sessions  = 4 hours
    • Contact session: 2 hours x 2 sessions in a week x 6 weeks = 24 hours
    • Self-study for calculation assignments: 1.5 hours x 12 assignments = 18 hours
    • Getting familiar with circuit simulation tool KiCad: 4 hours
    • Self-study for simulation assignments: 2 hours x 2 assignments = 4 hours
    In total, 4 + 24 + 18 + 4 + 4 = 54 hours. Note that, being able to complete the course in 54 hours assumes that students have right mathematical background and aim at grade 3. Those students who lag in background knowledge and/or aim at higher grades than 3 may have to use more than 54 hours.


    2.7 Grading criteria and evaluation method
    Total number of points is 48:
    • 8 points based on pre-assignments (2 points x 4 assignments).
    • 24 points based on calculation assignments (2 points x 12 assignments).
    • 16 points based on simulation assignments (8 points x 2 assignments).
    We guarantee that with 24 points the course is accepted, i.e., grade 1. Thresholds for grades 2 / 3 / 4 / 5 are tentatively 29 / 34 / 39 / 44 points, respectively.


    Questions? Share them!

    If you have questions of any sorts, post them to "General discussions" page. One of teachers will respond to the questions as soon as possible. Our discussions are visible to all our fellow colleagues registered in this course. In many cases, your questions are also points of clarification for your peers. It is therefore helpful to share questions and answers to all students registered in this course. You can send an individual question email to teachers, but do so only when it is a private issue.