AXM-E7011 - Digital Fabrication Studio, Lecture, 24.4.2024-7.6.2024
Kurssiasetusten perusteella kurssi on päättynyt 07.06.2024 Etsi kursseja: AXM-E7011
Osion kuvaus
-
Welcome to Digital Fabrication Studio!
This course covers 3/3 of the topics from Fab Academy.
As said on the Fab Academy website: "The Fab Academy is a fast-paced, hands-on learning experience where students learn rapid prototyping by planning and executing a new project each week, resulting in a personal portfolio of technical accomplishments."
Each week consists of the following.
- Global lecture
- Local lecture
- Assignment
Global lectures
Global lectures use Eastern Standard Time (think New York time) and are happening on Wednesdays 9:00 EST which at the beginning of the course is 16:00 Helsinki time. Use tools such as the 24 Time Zones to double-check. You can find the Zoom link at the bottom of the page.
Local lectures
Thursdays 13:15 online or hybrid mode depending on the topic. Please find the Zoom link below. Hybrid mode means that you can join the lecture physically at the Aalto Fablab and via Zoom.
Resources
Each topic has a basic set of skills that you will need to accomplish your assignment. Each week's page contains a list of resources you can use to learn the basics.
Sometimes the videos and tutorials do not explain everything. This is why you are encouraged to spend time at the lab, experiment on your own and ask instructors for guidance.
Human resources are precious. Whenever possible, try robots first. Search engines are your friends in this course. A course like this would not be possible without the internet. ChatGPT, Copilot? Why not. Use it!
Attendance
Use the attendance sheet to mark your participation in the lectures. You can find the attendance sheet at the bottom of this page. You are required to participate in 80% of the lectures to be able to pass the course.
Independent work
Lectures are there to guide you, but you are responsible for allocating enough time to complete the assignments yourself. Starting from week 05 (Computer-Controlled Cutting), you are supposed to plan your work to be able to spend time at the Aalto Fablab. That means being there not only during the lectures but whenever possible to complete your assignments. Start early and add buffer time to accommodate failed attempts.
The course is a full-time effort. It is recommended NOT to combine it with other courses. You will fail, and you will need time to recover. Keeping up with documentation takes time. It is in your best interest to make a good-looking portfolio of accomplishments as a result.
Individual Tutoring
Time is precious for everyone. In the case you need one-to-one guidance from the teacher, please schedule a meeting by contacting teachers via email.
Machine booking
Machines are pre-booked for the course participants for the specific weeks covering them. For example, vinyl cutter and laser cutter are booked for course participants during week 5 (Computer-Controlled Cutting), and the machines are expected to be used on a first-come, first-served basis, except when we are doing introductions. Introductions will happen on Thursdays and Fridays. Check the assignment pages to find links to specific booking options.
Outside the weeks covering a specific topic, you need to book the machines using the methods provided by Aalto Fablab. You can find the latest information about booking machines on the Aalto Fablab website.
Assignments
Every week you are supposed to do independent work and document it to complete an assignment. The first weeks of the course are the time when you learn the tools and the flow for documenting your assignments.
You can find the assignments in each of the weekly topic sections. Since you will be using GitLab to document your work, you must submit a link to a page on your website covering a specific topic.
Evaluation
Your work is going to be evaluated based on the documentation you produce. Invest time and energy during the first weeks of the course to master the flow of documenting on the go. Do not leave documentation to the very last minute of the course.
Grading is based on the following criteria.
1: The assignment has been submitted, and a page about the topic has been created.
2: Basic concepts of the assignment week are described, but not all of the requirements are met.
3: Minimum viable requirements of the assignment are met.
4: Creativity in the execution of the assignment can be seen. The topic has been explored beyond basic concepts.
5: The result is creative and technically impressive, and the documentation page itself can be used as a resource by someone else.
Refer to the official Fab Academy Assessment Guide to learn more about what is expected for each assignment. This is a documentation website you should be aiming for: Fab Academy by Nadieh Bremer.
-
Zoom link for local lectures Verkko-osoite
Passcode: DFAB2024
-
Zoom link for global lectures Verkko-osoite
Use password 1234
-
Realtime communication Verkko-osoite
Use this link to access the class real-time communication Telegram group.
-
File sharing Verkko-osoite
You will be able to find lecture recordings and other relevant information in the DF II shared folder.
Password: DigitalFabrication2024 -
Global Lecture Video Recordings Verkko-osoite
Here you can find the recorded global lecture videos.
-
Global Lecture Schedule Verkko-osoite
Fab Academy global lecture schedule.
-
List of student documentation pages Verkko-osoite
You can find the full list of student documentation repositories and websites here.
-
1 to 1 Troubleshooting Booking Verkko-osoite
Pick a 30 minute face-to-face troubleshooting session at the Fablab.
-
Video: Tips and Tricks Verkko-osoite
A collection of videos with all kinds of small tips and tricks that you can (should) use to improve the quality of your project. That includes cable crimping, soldering tricky chips et cetera.